DS20U7V2
  • Fanless and Silent
    Passive cooling, no fan noise at all
    Perfect to be used in noise-sensitive environments
    Fanless, dust-free and thus virtually maintenance-free
  • Low Power Consumption
    Power consumption in idle mode with 2.5" SSD under Windows 10: ca. 6 W only
  • 24/7 Nonstop Operation
    This device is approved for 24/7 permanent operation.
    Requirements:
    - Free circulation of air amongst the PC must be guaranteed.
    - Ventilation holes must stay clear.
    - If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
  • Chassis
    Slim-PC with black steel chassis
    Without cooling fan, passive cooling only
    The bays for memory, 2.5" drive and M.2 card
    can easily be accessed by removing two cover plates.
    Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
    Weight: 1.5 kg net and 2.2 kg gross
    Two holes for Kensington Lock and numerous 
    threaded holes (M3) at both sides of the chassis
  • Operating Position
    1) Vertical: Usual operating position with the supplied feet (DisplayPort output facing up).
    2) VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.
    Note: From a thermal point of view horizontal operation is permitted. However, there are no rubber feet on the device. The maximum operating temperature is 35 °C then.
  • Operating System
    This barebone system comes without operating system.
    It is compatible with Windows 10/11 (64-bit) and Linux (64-bit).
  • Processor
    Model: Intel Core i7-10510U (ULV)
    System-on-a-chip architecture (SoC) with integrated memory and graphics controller
    FCBGA1528 package - directly soldered onto the mainboard
    Code name: Comet Lake U (10th Generation Intel Core)
    Cores / Threads: 4 / 8
    Base frequency: 1.8 GHz
    Max. Turbo frequency: 4.9 GHz
    Intel Smart Cache: 8 MB
    TDP wattage: 15 W maximum
    Manufacturing process: 14nm
    Maximum Tjunction Temperature: 100 °C
    Supports 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2
  • Integrated Graphics
    Intel UHD Graphics
    GPU clock frequency: 300~1150 MHz
    Execution Units (EUs): 24
    Supports DirectX 12, OpenGL 4.5
    Supports full H264, H265 8/10 bit, VP8/9, VC-1, AVC hardware decoding
    Supports Quick Sync Video and Clear Video HD technology
    Supports up to three independent screens:
    1) DisplayPort 1.2 supports Ultra HD @ 60 Hz
    2) HDMI 2.0a supports Ultra HD @ 60 Hz
    3) D-Sub/VGA supports analog displays
  • Mainboard / BIOS
    Shuttle Mainboard FS20
    All capacitors are high quality solid capacitors
    Supports resume after power failure [6]
    Supports Wake on LAN (WOL)
    Supports Power on by RTC Alarm
    Supports boot from M.2 SSD cards und USB devices
    AMI BIOS in 16 MByte EEPROM with SPI interface
    Supports hardware monitoring and Watchdog function
    Supports Unified Extensible Firmware Interface (UEFI)
    Supports Firmware-TPM (fTPM) Version 2.0
  • Power Adapter
    External 65 W power adapter (fanless)
    Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
    Output: 19 V DC, max. 3.42 A, max. 65 W
    DC cable length: ca. 170 cm
    AC cable length: ca. 170 cm (3-pin Micky MM C6 and Schuko earthed safety plug)
  • DC Input connector
    DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)
    The DC-input of the computer supports an external
    power source with either 12V±5% or 19V±5%.
  • Memory support
    2x SO-DIMM slot with 260 pins
    Supports DDR4-2666 (PC4-21300) SDRAM at 1.2 V
    Supports DDR4-3200 at 2666 MHz
    Supports Dual Channel mode
    Supports a maximum of 32 GB per DIMM,
    maximum total size: 64 GB
    Supports two unbuffered DIMM modules (no ECC or registered)
  • 2.5" Drive Bay with SATA connector
    Supports one Serial ATA hard disk
    or one SATA SSD drive in 6.35 cm / 2.5" format
    Device height: max. 12.5 mm
    Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
    Supports Unified Extensible Firmware Interface (UEFI)
    Note: no Serial ATA cable is required.
  • M.2 Slot for SSDs
    The M.2 2280 BM slot provides the following interfaces:
    - PCI-Express Gen. 3.0 X4
    - SATA v3.0 (max. 6 Gbps)
    It supports M.2 cards with a width of 22 mm
    and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
    Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe NVMe SSDs (with M key)
    Supplied thermal pad for cooling M.2 SSDs.
  • M.2-2230E slot for WLAN cards
    Interfaces: PCI-Express Gen. 2.0 X1 und USB 2.0
    Supports M.2 cards with a width of 22 mm and a length of 30 mm (type 2230)
    Supports WLAN expansion cards (optional Shuttle accessory: WLN-M / WLN-M1)
    2x pre-installed antenna cables
  • Card Reader
    Integrated SD card reader
    Supports SD, SDHC and SDXC memory flash cards
  • Audio
    Audio Realtek® ALC897 or ALC 662 High-Definition Audio
    Two analog audio connectors (3.5 mm) at the front panel:
    1) 2 channel line out (headphones)
    2) microphone input
    Digital multi-channel audio output: via HDMI and DisplayPort
  • Dual LAN (2.5G + 1G)
    Dual network with two RJ45 ports
    Used network chips:
    1) left: Intel i211 Ethernet Controller supports 2.500 / 1.000 / 100 Mbps operation
    2) right: Intel i219 Ethernet Controller supports 1.000 / 100 / 10 Mbps operation
    Supports WAKE ON LAN (WOL)
    Supports network boot by Preboot eXecution Environment (PXE)
  • Prepared for Wireless Network (WLAN)
    2x pre-installed antenna cables (WLAN card and antennas not included)
    Prepared for the installation of an M.2-2242 WLAN card and two external antennas
  • Front Panel connectors/buttons
    2x USB 3.2 Gen 2 (red, max. 10 Gbps)
    4x USB 2.0
    Microphone input
    Audio Line-out (headphones)
    SD card reader (supports SD, SDHC, SDXC)
    Power button
    Power LED (blue)
    HDD LED (yellow)
  • Back Panel connectors
    DisplayPort 1.2 [3]
    HDMI 2.0a
    D-Sub/VGA
    2x USB 3.2 Gen 2 (red, max. 10 Gbps)
    2x Intel RJ45 LAN (left: 2.5 Gbps and right: 1 Gbps)
    Serial COM port (5V / 12V, switchable to RS232 / RS422 / RS485) [1]
    DC-input connector for external power adapter
    4-pin connector (2.54 mm pitch) for power button, Clear CMOS and 5 V DC [4]
  • Always-On Jumper
    By removing Jumper J9 (please refer to the quick user guide),
    the system will start unconditionally once power is applied. [6]
  • Scope of Delivery
    Multi-language user guide
    Two metal feet with four screws M3 x 7 mm
    VESA mount for 75/100mm standard (two metal brackets)
    Four screws M3 x 7 mm (screws together VESA mount and PC)
    Four screws M4 x 10 mm (to fix the VESA mount to the external surface)
    Two screws M3 x 5 mm to mount a 2.5" storage in the bay
    Two screws M3 x 5 mm to mount M.2 cards
    Thermal pad for cooling M.2 SSDs
    Driver DVD for Windows
    External 65W power adapter with power cord (with protective-earth contacts)
  • Optional Accessories
    - PCP11: adapter cable for the second COM port (replaces the VGA port)
    - CXP01: adapter cable for external power button
    - WWN03: LTE adapter kit for the 2.5" bay including two external LTE antennas [2]
    - WLN-M / WLN-M1: WLAN module (supports WLAN/Bluetooth) with two external antennas and cables
    - PRM01: 2U rack mount front plate for two Shuttle XPC slim
    - DIR01: mounting kit for 35 mm DIN-Rail
  • Environmental Specifications
    Operating temperature range: 0~40 °C [5]
    Relative humidity, non-condensing: 10~90 %
  • Conformity & Certifications
    EMI: CE, FCC, BSMI, RCM, VCCI
    Safety: CB, BSMI, cTUVus
    Other: RoHS, Energy Star, ErP
    This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
    (1) 2014/30/EU relating to electromagnetic compatibility (EMC)
    (2) 2014/35/EU relating to Electrical Equipment designed for use within certain voltage limits (LVD)
    (3) 2009/125/EC relating to eco design requirements for energy-related products (ErP)

Footnote:

[1] Jumper for COM port configuration
Pin 9 of the COM-Port is a multi-functional signal. Based on the Jumper JP1 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately. The operating mode of COM 1 can be set to RS232, RS422 or RS485 in the BIOS.
The second COM port (COM 2) supports RS232 mode only, and in the standard SKU of this product it is only available as an onboard connector on the mainboard. An appropriate adapter (e.g. the optional accessory PCP11) is required in order to provide this port as D-Sub connector at the back panel. In this case the VGA port cannot be used.

[2] LTE Adapter Kit WWN03
Using the LTE adapter kit WWN03 means, that the 2.5" bay can no longer be used for SATA drives in 2.5" format (hard disk or SSD). An SSD card in the M.2-2280 format must be used instead.

[3] How to convert DisplayPort into HDMI/DVI
The DisplayPort output can be converted to HDMI or DVI by an additional, passive adapter cable. For example:
DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)
DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)
The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either through DisplayPort (without an adapter) or HDMI/DVI (with an adapter).
However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter.

[4] Four-pin header at the back panel
This header allows for connecting an external power button.
It also provides 5 V DC voltage for external devices and the Clear CMOS function. Optional accessory: the adapter cable CXP01.

[5] Caution: For ambient temperatures higher than 35 °C we strongly recommend to use an SSD instead of an HDD

[6] Power on after power fail:
The BIOS setup provides a "Power-On after Power Fail" function that can be found under "Power Management Configuration". This function determines the PC's behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why this product also comes with a hardware-based solution. By removing Jumper J9 (please refer to the quick user guide), the system will start unconditionally once power is applied.